Connecting cable 10m M8 3-pole straight
Available downloads for "Connecting cable 10m M8 3-pole straight"
Login
Product information "Connecting cable 10m M8 3-pole straight"
| Cable outlet: | straight |
|---|---|
| Connecting cable: | 3-pin |
| Connecting cable length: | 10 m |
| Display LED: | No |
| Plug type: | Plug M8x1 |
| Protection circuit: | No |
| Shielded cable: | No |
| Type: | Sensor |
Accessory Items
2K Valve ID4/4
Article number: 401.06.40
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Hand metering valve 0.003-0.2ml
Article number: 1015590
Needle metering valves are suitable for dot application of low to high viscosity media. With this series, very small quantities of up to 3 ml per shot can be discharged with high reproducibility and short cycle times. The valve consists of two structurally separate parts, meaning that material cannot leak into the drive cylinder and interfere with the movement of the valve needle. This feature makes the needle metering valve an exceptionally reliable and low-maintenance piece of metering equipment. Shot size is determined by the volume of the valve chamber, which can be adjusted simply within a predetermined range using a stop screw. The metering cycle can be controlled either pneumatically or electrically via a solenoid valve. DOPAG needle metering valves are perfectly suitable for manual applications with a handle as well as for fully automated processes.
Price on request
2K Valve ID2/2
Article number: 402.05.21
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Hand dispensing valve ID2.5
Article number: 1019415
Based on the time-pressure dispensing principle, the needle dispensing valves are most effective in continuous applications of low to high viscosity media. Consisting of two structurally separate parts, they have the advantage that material cannot leak into the drive cylinder and interfere with the valve needle movement. The size of the orifice is regulated simply by a stop screw. A special, adjustable seal closes the valve needle off from the valve head, ensuring a perfectly clean and precise application of every single shot. The material passageway can be flushed as and when necessary.
Price on request
2K Valve ID2/2
Article number: 402.05.23
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Dispensing valve ID12
Article number: 1026083
Based on the time-pressure dispensing principle, the needle dispensing valves are most effective in continuous applications of low to high viscosity media. Consisting of two structurally separate parts, they have the advantage that material cannot leak into the drive cylinder and interfere with the valve needle movement. The size of the orifice is regulated simply by a stop screw. A special, adjustable seal closes the valve needle off from the valve head, ensuring a perfectly clean and precise application of every single shot. The material passageway can be flushed as and when necessary.
Price on request
Hand metering valve 0.05-0.5ml
Article number: 1017833
Chamber metering valves are used for dot application of low to high viscosity media. Compared to the needle metering valve, they offer a larger range of shot sizes. Thanks to an innovative design that features a snuff back effect, these valves are characteristic for their high process stability and dripfree application when dispensing low-viscosity media. The shot size is determined by the chamber volume, which can be adjusted simply within a predetermined range using a stop screw. The metering cycle is controlled either pneumatically or electrically via a solenoid valve. This valve series allows a highly repeatable metering of small quantities up to 100 ml within short cycle times. Manual application with a handle is just as possible as the integration into a fully automated process.
Price on request
Mixing block ID4/1
Article number: 403.05.40
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
2K Valve ID8/8
Article number: 403.05.00
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Hand metering valve 0.05-0.5ml
Article number: 1017834
Chamber metering valves are used for dot application of low to high viscosity media. Compared to the needle metering valve, they offer a larger range of shot sizes. Thanks to an innovative design that features a snuff back effect, these valves are characteristic for their high process stability and dripfree application when dispensing low-viscosity media. The shot size is determined by the chamber volume, which can be adjusted simply within a predetermined range using a stop screw. The metering cycle is controlled either pneumatically or electrically via a solenoid valve. This valve series allows a highly repeatable metering of small quantities up to 100 ml within short cycle times. Manual application with a handle is just as possible as the integration into a fully automated process.
Price on request
2K Valve ID6/6
Article number: 400.17.04
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Mixing block ID4/2
Article number: 1011923
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Mixing block ID12/12
Article number: 560.30.52
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Mixing block ID4/1
Article number: 401.05.40
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Hand metering valve 0.003-0.2ml
Article number: 1017514
Needle metering valves are suitable for dot application of low to high viscosity media. With this series, very small quantities of up to 3 ml per shot can be discharged with high reproducibility and short cycle times. The valve consists of two structurally separate parts, meaning that material cannot leak into the drive cylinder and interfere with the movement of the valve needle. This feature makes the needle metering valve an exceptionally reliable and low-maintenance piece of metering equipment. Shot size is determined by the volume of the valve chamber, which can be adjusted simply within a predetermined range using a stop screw. The metering cycle can be controlled either pneumatically or electrically via a solenoid valve. DOPAG needle metering valves are perfectly suitable for manual applications with a handle as well as for fully automated processes.
Price on request
2K Valve ID4/4
Article number: 401.05.20
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Hand dispensing valve ID2.5
Article number: 1019639
Based on the time-pressure dispensing principle, the needle dispensing valves are most effective in continuous applications of low to high viscosity media. Consisting of two structurally separate parts, they have the advantage that material cannot leak into the drive cylinder and interfere with the valve needle movement. The size of the orifice is regulated simply by a stop screw. A special, adjustable seal closes the valve needle off from the valve head, ensuring a perfectly clean and precise application of every single shot. The material passageway can be flushed as and when necessary.
Price on request
2K Valve ID4/4
Article number: 401.06.60
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Hand metering valve 0.003-0.2ml
Article number: 1017829
Needle metering valves are suitable for dot application of low to high viscosity media. With this series, very small quantities of up to 3 ml per shot can be discharged with high reproducibility and short cycle times. The valve consists of two structurally separate parts, meaning that material cannot leak into the drive cylinder and interfere with the movement of the valve needle. This feature makes the needle metering valve an exceptionally reliable and low-maintenance piece of metering equipment. Shot size is determined by the volume of the valve chamber, which can be adjusted simply within a predetermined range using a stop screw. The metering cycle can be controlled either pneumatically or electrically via a solenoid valve. DOPAG needle metering valves are perfectly suitable for manual applications with a handle as well as for fully automated processes.
Price on request
2K Valve ID2/2
Article number: 402.05.22
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Dispensing valve ID1
Article number: 401.00.24
Based on the time-pressure dispensing principle, the needle dispensing valves are most effective in continuous applications of low to high viscosity media. Consisting of two structurally separate parts, they have the advantage that material cannot leak into the drive cylinder and interfere with the valve needle movement. The size of the orifice is regulated simply by a stop screw. A special, adjustable seal closes the valve needle off from the valve head, ensuring a perfectly clean and precise application of every single shot. The material passageway can be flushed as and when necessary.
Price on request
Hand metering valve 0.1-3ml
Article number: 1017476
Chamber metering valves are used for dot application of low to high viscosity media. Compared to the needle metering valve, they offer a larger range of shot sizes. Thanks to an innovative design that features a snuff back effect, these valves are characteristic for their high process stability and dripfree application when dispensing low-viscosity media. The shot size is determined by the chamber volume, which can be adjusted simply within a predetermined range using a stop screw. The metering cycle is controlled either pneumatically or electrically via a solenoid valve. This valve series allows a highly repeatable metering of small quantities up to 100 ml within short cycle times. Manual application with a handle is just as possible as the integration into a fully automated process.
Price on request
2K Valve ID4/4
Article number: 401.05.60
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
2K Valve ID8/8
Article number: 401.05.00
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Hand metering valve 0.1-3ml
Article number: 1017520
Chamber metering valves are used for dot application of low to high viscosity media. Compared to the needle metering valve, they offer a larger range of shot sizes. Thanks to an innovative design that features a snuff back effect, these valves are characteristic for their high process stability and dripfree application when dispensing low-viscosity media. The shot size is determined by the chamber volume, which can be adjusted simply within a predetermined range using a stop screw. The metering cycle is controlled either pneumatically or electrically via a solenoid valve. This valve series allows a highly repeatable metering of small quantities up to 100 ml within short cycle times. Manual application with a handle is just as possible as the integration into a fully automated process.
Price on request
2K Valve ID6/6
Article number: 400.17.03
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Mixing block ID4/4
Article number: 560.30.09
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Mixing block ID2/2
Article number: 560.30.13
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Mixing block ID8/8
Article number: 560.30.57
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Dispensing valve ID2.5
Article number: 401.09.01
Based on the time-pressure dispensing principle, the needle dispensing valves are most effective in continuous applications of low to high viscosity media. Consisting of two structurally separate parts, they have the advantage that material cannot leak into the drive cylinder and interfere with the valve needle movement. The size of the orifice is regulated simply by a stop screw. A special, adjustable seal closes the valve needle off from the valve head, ensuring a perfectly clean and precise application of every single shot. The material passageway can be flushed as and when necessary.
Price on request
2K Valve ID4/4
Article number: 400.05.60
DOPAG 2K valves are used to process 2K materials with similar viscosities and a relatively long pot life. Recommended mixing ratios are from 100:100 to 100:20. The static mixing system consists of pneumatic driven snuff back piston and a plastic mixer. Due to the infinitely adjustable snuff back function dripping is avoided when metering ends. Different sealing and material versions for chemically aggressive and abrasive 2K materials are available.
Price on request
Hand metering valve 0.003-0.2ml
Article number: 1017539
Needle metering valves are suitable for dot application of low to high viscosity media. With this series, very small quantities of up to 3 ml per shot can be discharged with high reproducibility and short cycle times. The valve consists of two structurally separate parts, meaning that material cannot leak into the drive cylinder and interfere with the movement of the valve needle. This feature makes the needle metering valve an exceptionally reliable and low-maintenance piece of metering equipment. Shot size is determined by the volume of the valve chamber, which can be adjusted simply within a predetermined range using a stop screw. The metering cycle can be controlled either pneumatically or electrically via a solenoid valve. DOPAG needle metering valves are perfectly suitable for manual applications with a handle as well as for fully automated processes.
Price on request